Az OTD140 kültéri router dedikált és strapabíró IP55-ös műanyag házzal és beépített rögzítővel rendelkezik, így ez a kültéri 4G router könnyen telepíthető, és képes ellenállni a kültéri környezeti feltételeknek. Ezen túlmenően ez a kültéri útválasztó fel van szerelve LTE Cat 4 csatlakozással, az RMS-szel kompatibilis a távoli felügyeleti képességekkel és két PoE-in/out Ethernet porttal.
OTD140
-
Leírás
-
Jellemzők
-
Csomag
-
Dokumentumok
Az OTD140 kültéri router dedikált és strapabíró IP55-ös műanyag házzal és beépített rögzítővel rendelkezik, így ez a kültéri 4G router könnyen telepíthető, és képes ellenállni a kültéri környezeti feltételeknek. Ezen túlmenően ez a kültéri útválasztó fel van szerelve LTE Cat 4 csatlakozással, az RMS-szel kompatibilis a távoli felügyeleti képességekkel és két PoE-in/out Ethernet porttal.
-
Mobile module
4G (LTE) - LTE Cat 4 150 Mbps DL, 50 Mbps UL; 3G - 21 Mbps DL, 5.76 Mbps UL; 2G - 236.8 kbps DL, 236.8 kbps UL
-
SIM switch
2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection
-
Status
Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID
-
SMS
SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP
-
USSD
Supports sending and reading Unstructured Supplementary Service Data messages
-
Black/White list
Operator black/white list
-
Band management
Band lock, Used band status display
-
APN
Auto APN
-
Bridge
Direct connection (bridge) between mobile ISP and device on LAN
-
Passthrough
Router assigns its mobile WAN IP address to another device on LAN
-
LAN
2 x ETH ports (can be configured as WAN), 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover
-
PoE ports
1 x PoE In
-
PoE standards
802.3af/at
-
PoE ports
1 x PoE Out
-
PoE standards
802.3af and 802.3at Alternative B
-
PoE Max Power per Port (at PSE)
24 W Max (power supply unit dependent)
-
Routing
Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing
-
Network protocols
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan (WOL)
-
VoIP passthrough support
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
-
Connection monitoring
Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection
-
Firewall
Port forward, traffic rules, custom rules
-
Firewall status page
View all your Firewall statistics, rules, and rule counters
-
Ports management
View device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on
-
Network topology
Visual representation of your network, showing which devices are connected to which other devices
-
DHCP
Static and dynamic IP allocation, DHCP Relay
-
QoS / Smart Queue Management (SQM)
Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
-
DDNS
Supported >25 service providers, others can be configured manually
-
Network backup
VRRP, Wired options, each of which can be used as an automatic Failover
-
Hotspot
Captive portal (Hotspot), internal/external Radius server, SMS authorization, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customizable themes and option to upload and download customised hotspot themes
-
SSHFS
Possibility to mount remote file system via SSH protocol
-
Authentication
Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & Login attempts block
-
Firewall
Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
-
Attack prevention
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
-
VLAN
Port and tag-based VLAN separation
-
Mobile quota control
Mobile data limit, customizable period, start time, warning limit, phone number
-
WEB filter
Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
-
Access control
Flexible access control of SSH, Web interface, CLI and Telnet
-
OpenVPN
Multiple clients and a server can run simultaneously, 27 encryption methods
-
OpenVPN Encryption
DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,
BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256
-
IPsec
IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)
-
GRE
GRE tunnel, GRE tunnel over IPsec support
-
PPTP, L2TP
Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support
-
Stunnel
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code
-
DMVPN
Method of building scalable IPsec VPNs
-
SSTP
SSTP client instance support
-
ZeroTier
ZeroTier VPN client support
-
WireGuard
WireGuard VPN client and server support
-
Tinc
Tinc offers encryption, authentication and compression in it's tunnels. Client and server support.
-
Supported modes
Client, Server (planned)
-
Supported connection types
TCP
-
Supported modes
Server, Client
-
Supported connection types
TCP
-
Custom registers
MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality
-
Supported data formats
8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII
-
Protocol
HTTP(S), MQTT, Azure MQTT
-
Data to server
Extract parameters from multiple sources and different protocols, and send them all to a single server
-
Modbus MQTT Gateway
Allows sending commands and receiving data from MODBUS Master through MQTT broker
-
Supported modes
Station, Outstation
-
Supported connection
TCP
-
DLMS Support
DLMS - standard protocol for utility meter data exchange
-
WEB UI
HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
-
FOTA
Firmware update from server, automatic notification
-
SSH
SSH (v1, v2)
-
SMS
SMS status, SMS configuration, send/read SMS via HTTP POST/GET
-
Call
Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer
-
TR-069
OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
-
MQTT
MQTT Broker, MQTT publisher
-
SNMP
SNMP (v1, v2, v3), SNMP Trap
-
JSON-RPC
Management API over HTTP/HTTPS
-
RMS
Teltonika Remote Management System (RMS)
-
Cloud of Things
Allows monitoring of: Device data, Mobile data, Network info, Availability
-
ThingWorx
Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
-
Cumulocity
Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength
-
Azure IoT Hub
Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type
-
CPU
Mediatek, 580 MHz, MIPS 24KEc
-
RAM
128 MB
-
FLASH storage
16 MB
-
WEB UI
Update FW from file, check FW on server, configuration profiles, configuration backup
-
FOTA
Update FW
-
RMS
Update FW/configuration for multiple devices at once
-
Keep settings
Update FW without losing current configuration
-
Operating system
RutOS (OpenWrt based Linux OS)
-
Supported languages
Busybox shell, Lua, C, C++, and Python, Java in Package manager
-
Development tools
SDK package with build environment provided
-
GPL customization
You can create your own custom, branded firmware and web page application by changing colours, logos, and other elements in our firmware to fit your or your clients’ needs.
-
Events
Email, RMS, SMS
-
Connector
RJ45 Socket
-
Input voltage range
42.5–57.0 VDC, reverse polarity protection, voltage surge/transient protection
-
Input voltage range for PoE
42.5–57.0 VDC, reverse polarity protection, voltage surge/transient protection
-
Power consumption
Idle: < 2.5 W / Max: < 6 W / PoE Max < 21 W
-
Ethernet
2 x RJ45 ports, 10/100 Mbps
-
Status LEDs
3 x Mobile connection type, 3 x Mobile connection strength, 4 x ETH status LEDs
-
SIM
2 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V
-
Power
RJ45, PoE In, 42.5 – 57.0 VDC
-
Antennas
2 x Internal antennas
-
Antennas specifications
1 x 698 - 960 / 1710 - 2690MHz, 50 Ω, VSWR <3.5, gain <3 dBi, omnidirectional
1 x 698 - 960 / 1710 - 2690MHz, 50 Ω, VSWR <3, gain <4.5 dBi, omnidirectional
-
Reset
Reboot/User default reset/Factory reset button
-
Casing material
Plastic (PC+ASA)
-
Dimensions (W x H x D)
110 x 49.30 x 235 mm
-
Weight
855 g
-
Mounting options
Mounting Bracket (for vertical flat surface or pole mounting)
-
Operating temperature
-40 °C to 75 °C
-
Operating humidity
10% to 90% non-condensing
-
Ingress Protection Rating
IP55
-
Regulatory
CE, UKCA, EAC, UCRF, RCM
STANDARD PACKAGE
- OTD140 Router
- Router Holder
- QSG (Quick Start Guide)
- Packaging Box